Smoke Alarm Installation and Maintenance

It’s important to have enough smoke alarms in your home. Fire research has demonstrated that with today’s modern furnishings, fires can spread much more rapidly than in the past when more natural materials were used. Because of this, having a sufficient number of properly located smoke alarms is essential to maximize the amount of available escape time. For many years the National Fire Protection Association (NFPA), has required as a minimum that smoke alarms be installed inside every sleep room (even for existing homes) in addition to requiring them outside each sleeping area and on every level of the home. (Additional smoke alarms are required for larger homes.) Homes built to earlier standards often don’t meet these minimum requirements. Homeowners should recognize that detection needs have changed over the years and one should take proactive steps make sure that every home has a sufficient complement of smoke alarms. Smoke alarms should be installed according to NFPA 72 and the manufacturer's instructions. In addition, the smoke alarm you select should also bear the Underwriters Laboratory.

Alarm Placement

Heat and smoke rise, so smoke alarms should be installed on the ceiling or high on a wall to detect the first traces of smoke. If a room has a pitched (slanted) ceiling, mount the unit near the ceiling’s highest point, 4 to 12 inches (10 to 30.5 centimeters) away from the wall. If the room has an A-frame ceiling, mount the unit at least 4 to 12 inches (10 to 30.5 centimeters) away from the peak. Avoid placing alarms in ceiling corners as the alarm may not work properly in this location.

 

Wall-mounted smoke alarms should be installed so that the top of the alarm is not more than 12 inches (30.5 centimeters) from the ceiling. Install basement smoke alarms close to the bottom of the stairs. Don’t install an alarm at the top of basement stairs; dead air trapped near the closed door could prevent smoke from reaching the unit. Some household environments can cause nuisance alarms or interfere with a smoke alarm’s operation. Avoid placing alarms near a cooking appliance, a dusty area, a shower, or any area where the temperature drops below 40°F (4.5°C) or rises above 110°F (43°C).

Cooking fumes, steam, and automobile exhaust can result in nuisance alarms. Do not install alarms in bathrooms, kitchens, garages, attics, or unheated areas or near recessed ceiling areas, ceiling fans, furnaces, or furnace vents. Place alarms at least 3 feet (0.9 meter) horizontally from bathroom doors.

Installing Smoke Alarms

Choose smoke alarms that have the label of a recognized testing laboratory like Underwriters Laboratory.

Install smoke alarms inside each bedroom, outside each sleeping area and on every level of the home, including the basement.

On levels without bedrooms, install alarms in the living room (or den or family room) or near the stairway to the upper level, or in both locations.

Smoke alarms installed in the basement should be installed on the ceiling at the bottom of the stairs leading to the next level.

Smoke alarms should be installed at least 10 feet (3 meters) from a cooking appliance to minimize false alarms when cooking.

Mount smoke alarms high on walls or ceilings (remember, smoke rises). Wall-mounted alarms should be installed not more than 12 inches away from the ceiling (to the top of the alarm).

If you have ceilings that are pitched, install the alarm within 3 feet of the peak but not within the apex of the peak (four inches down from the peak).

Don't install smoke alarms near windows, doors, or ducts where drafts might interfere with their operation.

Never paint smoke alarms. Paint, stickers, or other decorations could keep the alarms from working.

For the best protection, interconnect all smoke alarms. When one smoke alarm sounds they all sound. Interconnection can be done using hard-wiring or wireless technology.

When interconnected smoke alarms are installed, it is important that all of the alarms are from the same manufacturer. If the alarms are not compatible, they may not sound.

There are two types of smoke alarms – ionization and photoelectric. An ionization smoke alarm is generally more responsive to flaming fires, and a photoelectric smoke alarm is generally more responsive to smoldering fires. For the best protection, both types of alarms or combination ionization-photoelectric alarms, also known as dual sensor smoke alarms, are recommended.

Keep manufacturer’s instructions for reference.


Testing Smoke Alarms

• Smoke alarms should be maintained according to manufacturer's instructions.


• Test smoke alarms at least once a month using the test button.


• Make sure everyone in the home understands the sound of the smoke alarm and knows how to respond.


• Follow manufacturer’s instructions for cleaning to keep smoke alarms working well. The instructions are included in the package or can be found on the internet.


• Smoke alarms with non-replaceable 10-year batteries are designed to remain effective for up to 10 years. If the alarm chirps, warning that the battery is low, replace the entire smoke alarm right away.


• Smoke alarms with any other type of battery need a new battery at least once a year. If that alarm chirps, warning the battery is low, replace the battery right away.


• When replacing a battery, follow manufacturer’s list of batteries on the back of the alarm or manufacturer’s instructions. Manufacturer’s instructions are specific to the batteries (brand and model) that must be used. The smoke alarm may not work properly if a different kind of battery is used.